Moto E5 Plus Row (XT1924) - Manual de Servicio

SAVE OFFLINE

Moto E Plus (5th Generation) ROW

Moto E (4th Ge s n.) u l P

Moto E (4th Ge n . ) FIDENTIAL REST R I C CON TED

VO

OVO CONFIDENTIA LEN L

RE S TR IC T ED

VO NO LE

CO NF I

R

E (4th Ge n Moto . ) P

08/18/2017 lus

LEN OV O

o E (4th Gen. t o )P M l

us

STRICTED AL RE I T N IDE F N CO

LENOVO C ONF IDE NT IA L

D TE IC TR ES

ICTED R T S RE L A TI N DE

L E NO

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

REVISION HISTORY Revision 1

PAGE 2

Date

Notes

05/03/18

Initial draft.

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

TABLE OF CONTENTS Revision History.................................................................................................................................. 2 List of Tables ....................................................................................................................................... 5 Table of Figures .................................................................................................................................. 5 Safety Information .............................................................................................................................. 6 Cautions and Warnings ....................................................................................................................... 6 Battery Safety Guidelines .................................................................................................................... 6 Introduction ......................................................................................................................................... 7 External Views..................................................................................................................................... 7 Main Exploded Views .......................................................................................................................... 9 Disassembly and Recovery ............................................................................................................. 12 Disassembly and Recovery Map....................................................................................................... 12 Tools Required for Disassembly ....................................................................................................... 13 SIM Tray Removal ............................................................................................................................ 15 IMEI Label Removal .......................................................................................................................... 16 Water Detection Label Inspection ..................................................................................................... 17 Battery Inlay Removal ....................................................................................................................... 18 Screw Tampering Label Inspection ................................................................................................... 27 Finger Print Sensor Flex Removal .................................................................................................... 28 Rear Housing Removal ..................................................................................................................... 29 Rear-Facing Imager Deco and Imager Lens Removal ..................................................................... 30 Water Detection Label Inspection ..................................................................................................... 32 Main PCB Removal ........................................................................................................................... 33 Earpiece Speaker Removal .............................................................................................................. 36 Factory Track ID Label Removal....................................................................................................... 37 Headset Jack Grommet Removal ..................................................................................................... 38 Rear-Facing Laser Rubber Removal ................................................................................................ 39 Rear-Facing Imager Removal ........................................................................................................... 40 Front-Facing Imager Removal .......................................................................................................... 41 Front-Facing Camera Rubber Removal ............................................................................................ 42 Proximity Sensor Grommet Removal ................................................................................................ 43 Shield Heat Spreading Pad Removal ............................................................................................... 44 Battery Removal ................................................................................................................................ 45 Side-Key Flex and Side Key Removal .............................................................................................. 47 Lower PCB and Cover Removal ....................................................................................................... 48 Main Flex Removal ........................................................................................................................... 49 Coax Cable Removal ........................................................................................................................ 50 USB Grommet Removal .................................................................................................................... 51

PAGE 3

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Vibrator Removal .............................................................................................................................. 52 Parts Refresh ..................................................................................................................................... 53 Tools Required for Parts Refresh ..................................................................................................... 53 Front Housing Cleaning .................................................................................................................... 54 Rear Housing Cleaning ..................................................................................................................... 55 Battery Inlay Cleaning ....................................................................................................................... 56 Assembly ........................................................................................................................................... 57 Assembly Map ................................................................................................................................... 57 Tools Required for Assembly ............................................................................................................ 59 Side-Key Flex and Side-Key Assembly ............................................................................................ 61 USB Grommet Assembly .................................................................................................................. 63 Vibrator Assembly ............................................................................................................................. 64 Main Flex Assembly .......................................................................................................................... 65 Lower PCB and Cover Assembly ...................................................................................................... 67 Front-Facing Camera Rubber Assembly .......................................................................................... 69 Shield Heat Spreading Pad Assembly .............................................................................................. 70 Front-Facing Imager Assembly ......................................................................................................... 71 Proximity Sensor Grommet Assembly .............................................................................................. 72 Rear-Facing Imager Assembly.......................................................................................................... 73 Rear-Facing Laser Rubber Assembly ............................................................................................... 74 Headset Jack Grommet Assembly .................................................................................................... 75 Factory Track ID Label Assembly ..................................................................................................... 76 Main PCB Assembly ......................................................................................................................... 77 Water Detection Label Assembly ...................................................................................................... 80 Earpiece Speaker Assembly ............................................................................................................. 81 Battery Assembly .............................................................................................................................. 82 Rear-Facing Imager Deco and Imager Lens Assembly .................................................................... 92 Rear Housing Assembly.................................................................................................................... 93 Finger Print Sensor Flex Assembly ................................................................................................... 94 Screw Tampering Label Assembly ................................................................................................... 95 Battery Inlay Adhesive Assembly ...................................................................................................... 96 Battery Inlay Assembly...................................................................................................................... 99 IMEI Label Assembly ...................................................................................................................... 100 Sim Tray Assembly ......................................................................................................................... 101

PAGE 4

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

LIST OF TABLES Table 1. External Views Parts List ........................................................................................................ 8 Table 2. Assembly Exploded View Parts List ....................................................................................... 9

TABLE OF FIGURES Figure 1. External Views ....................................................................................................................... 7 Figure 2. Assembly Exploded View ...................................................................................................... 9

PAGE 5

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

SAFETY INFORMATION Cautions and Warnings Electrostatic Discharge The phone components may be damaged by electrostatic discharge (ESD). Always use an ESD mat and ground strap when working with internal components.

Battery Safety Guidelines Handle Battery with care. Ensure Battery edges and surfaces are not dented or deformed. If the Battery Pack is dropped to the floor, it may be internally damaged and must be scrapped. Ensure all surfaces, fixtures, and phone components contacting the Battery are smooth and clean. Ensure Battery and its insulation are not damaged (e.g. scratched, dented, punctured) prior to and throughout assembly. Prior to assembly, ensure Battery edges and surfaces are not dented or deformed, and that fixtures and parts that will contact the Battery are free of foreign material. Ensure screws and screwdrivers do not contact the Battery. Failure to adhere to Safety Critical Note(s) may increase risk of rupture, burning, or failure to function safely when used by the customer.

PAGE 6

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

INTRODUCTION External Views

Figure 1. External Views

PAGE 7

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Table 1. External Views Parts List

Reference #

PAGE 8

Description

1

Front Housing

2

SIM Door

3

Speaker

4

FF Flash

5

Main Lens

6

Volume Key

7

Power Key

8

Rear Facing Camera

9

Flash

10

FPS

11

Rear Housing

12

Regulatory Label

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Main Exploded Views

Figure 2. Assembly Exploded View Table 2. Assembly Exploded View Parts List

Reference #

Description

Recovery Part

1

LC+Y50409395+mkey(DPgrey) LC+Y50409406+mkey(DPgold) XT1924 VolumeKey BL&5040AA000004 CS

YES

2

XT1924 TP+LCM ASSY_GR&5079AA000015 CS XT1924 TP+LCM ASSY_GL&5079AA000014 CS XT1924 TP+LCM ASSY_BL&5079AA000017CS

YES

3

LC+Y26209646+tfospeaker

NO

4

LC+Y26409054+L3100_Camera_500W_F

YES

5

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

YES

6

LC+Y506010055+jacksi(DP)

NO

7

MDL,CAMR,12MP,L12AA00 AF 30 COB OFILM

YES

8

LC+Y506010057+FCsi_5M(DP)

NO

9

LC+Y506010056+lightsi(DP)

NO

10

LC+Y506010077+sensi(DP)

NO

PAGE 9

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Reference #

Description

Recovery Part

11

LC+Y501110312+basm(HCgre) LC+Y501110314+bam(HCgold) XT1924 BatteryCover BL&5011AA000025 CS

YES

12

LC+Y50409394+pkey(DPgrey) LC+Y50409405+pkey(DPgold) XT1924 PowerKey BL&5040AA000006 CS

NO

13

XT1924 Sub Board&6818AA000040 CS XT1924-3 IN SUB PCBA

NO

14

LC+Y26223381+motor_FPC

NO

15

LC+Y53219447+bopante(SBD)

YES

16

LC+Y66802486+skeyfpc(AWX)

NO

17

LC+Y66802482+mainfpc(AWX)

NO

18

LC+Y52341631+RF(DL)

NO

19

LY,HE50,AMPEREX TYP5000MAH

NO

20

XT1924 Bracket_top ASSY&7601AA000030 CS

NO

21

LC+Y57200381+Cde(HXgrey) LC+Y57200388+Cde(HX_gold) XT1924-6 CAM Deco_BL&5015AA000009 CS

NO

22

LC+Y50309690+BCLE(SS_bla)

NO

23

MDL,FNGRPRT,Emma,BLK,SLVR,GRY,Kerr MDL,FNGRPRT,Emma,BLK,SLVR,GLD,Kerr MDL,FNGRPRT,Emma,BLK,BLK,BLK,Kerr

YES

24

LC+Y50902039+FPpreasm(LM)

NO

25

LC+Y54509522+FPefoa(LVHUI)

NO

26

LC+Y46369167+stray(Ogrey) LC+Y46369193+stray(Ogold) XT1924 SIM Tray BL&5017AA000010 CS LC+Y46369196+ostray(Ogrey) LC+Y46369194+ostray(Ogold)

YES

--

LBL,IMEI,IMEI,GHOST

NO

--

LC+Y70151569+LXF_L3600_A01LDI_label

NO

--

LC+Y54509533+PCBAmy(LVHUI)

NO

--

LC+Y46809739+Fspkfo(LVHUI)

NO

--

LC+Y46809738+Bspkfo(LVHUI)

NO

--

LC+Y46809741+BCflfo(LVHUI)

NO

--

LC+Y50902041+FC_gcasm(LM)

NO

--

LC+Y5430SK000080+BAfoam(LVHUI)

NO

--

XT1924 shield thm pad-4GPA&5460AA000027 CS

NO

--

XT1924 shield thm pad-BB PMU&5460AA000028 CS

NO

PAGE 10

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Reference #

Description

Recovery Part

--

XT1924 shield thm pad-CPU&5460AA000029 CS

NO

--

LC+Y54509532+FPstfa(LVHUI)

NO

--

LC+Y46106115+screwM1.4

NO

--

LC+Y46106126+screw_M14_16

NO

--

LC+Y70157057+LXF_L3500_A01_Fragile_Label

NO

--

LC+Y46106085+LXF_L3510_A01_SCREW

NO

--

XT1924 main FPC tape&5450AA000020 CS

NO

--

XT1924 Motor FPC tape&5420AA000030 CS

NO

--

XT1924 rear housing tape&5420AA000028 CS

NO

--

XT1924 Batt cover gule&5420AA000056 CS

NO

--

XT1924 FPS tape&5420AA000058 CS

NO

--

XT1924 Cam Deco tape&5420AA000032 CS

NO

--

XT1924 Cam lens tape&5420AA000060 CS

NO

--

XT1924 Side key metal tape&5420AA000032 CS

NO

--

LC+Y47201563+RFcfab(LVHUI)

NO

*Refer to this table as a reference to parts listed in the Assembly section.

PAGE 11

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

DISASSEMBLY AND RECOVERY Disassembly and Recovery Map *Shaded parts may be eligible for parts recovery.

PAGE 12

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Tools Required for Disassembly The following tools are required to disassemble the Moto E Plus (5th Generation) phone.

Description

Battery Inlay/Display Removal Fixture

Part #

Picture / Drawing

MR-M2-001

Moto E5 Plus Insert

MR-M2-001-022 (Crystal)

Battery Inlay Heat Plate

3-00-T4-10000

Hot Plate

--

Thin Plastic Spudger

--

SIM/SD Tray Removal Tool

--

PAGE 13

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Description

Part #

Black Stick

--

Torque Driver

--

ph00 Bit

--

Shim

--

Tweezers (Metal)

--

--

Tweezers (Plastic)

--

--

ESD Mat

--

--

Wrist Strap

--

--

Gloves or Finger Collets

--

--

PAGE 14

Picture / Drawing

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

SIM Tray Removal NOTE The SIM Tray can be recovered and reused after removal. 1.

Use the SIM Tray Removal pin to push into the SIM Tray hole as shown.

2.

Press the pin into the SIM Tray to make it popout. Use your fingers to remove the SIM Tray.

PAGE 15

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

IMEI Label Removal NOTE Remove the IMEI Label only if necessary. After you remove it, you cannot reuse it. Use the Tweezer to remove the IMEI Label from the SIM tray.

PAGE 16

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Water Detection Label Inspection NOTE If the Water Detection Label (WDL) is activated, the phone’s warranty no longer applies. Inspect the WDL inside the SIM Tray Slot for signs of activation. Use external light if needed.

PAGE 17

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Inlay Removal Preheating for Battery Inlay Removal NOTE The Battery Inlay can be recovered and reused after removal.

NOTE Battery Inlay Removal Methods A and B have the same preheating steps, as shown below. 1.

Place the Potter Lens Adhesive Heating Plate on the Hot Plate.

// CAUTION // Do not set the Hot Plate temperature higher than 80 °C (176 °F). Damage to the phone may occur. 1.

Set the Hot Plate to 80 °C (176 °F).

NOTE Preheating with an oven is also acceptable if the oven is set to the same temperature. 2.

Place the phone in the Heating Plate, with the Battery Inlay side down.

3.

Wait 10 minutes for the Battery Inlay Adhesive to warm up.

PAGE 18

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

4.

Remove the phone from the Heating Plate or the oven.

// CAUTION // Wear protective gloves when handling heated phones.

NOTE Perform the Battery Inlay removal procedure before the phone starts to cool off.

PAGE 19

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Inlay Removal Method A 1.

Use the 3 mm Allen Wrench to loosen the screws holding the side rails on the Battery Inlay Fixture. Do not remove the rails.

2.

Use the 3 mm Allen Wrench to remove the 2 center screws.

3.

Orient the Battery Inlay Removal Insert in relation to the battery Inlay Removal Fixture as shown. Place the Insert in the Battery Inlay Removal Fixture.

4.

Use the 3 mm Allen Wrench on the 2 center screws to tighten the Battery Inlay Removal Insert into position.

PAGE 20

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

5.

Slide both side rails on the Battery Inlay Fixture firmly against the Battery Inlay Insert. Use the 3 mm Allen Wrench to tighten the 4 outside screws on the underside of the Battery Inlay Fixture.

6.

Follow preheating steps described on Page 18.

7.

Slide the phone into the Battery Inlay Fixture as shown. Center the phone in the Fixture.

8.

Place the alignment pin on the Insert in the Headset Jack opening on the phone as shown.

9.

Press down on the Battery Inlay Fixture handle to bring the suction cups in contact with the Battery Inlay. Make sure all suction cups are attached to the Battery Inlay.

// CAUTION // Use care when pressing down on the Battery Inlay Fixture handle. Damage to the phone may occur.

PAGE 21

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

NOTE Begin this step before the phone starts to cool off. 10. As the Battery Inlay begins to release from the phone, use the Thin Plastic Spudger to gently pry the Inlay as shown.

// CAUTION // Do not insert the Thin Plastic Spudger more than 10 mm to prevent damaging internal components. 11. Use the Thin Plastic Spudger to loosen or cut the adhesive holding the Battery Inlay. If necessary, reheat the phone using a Heat Gun as you work your way around the edges of the phone.

// CAUTION // Use care to prevent damage to the FPS Flex.

// CAUTION // Use care not to bend the Battery Inlay. Damage to the phone may occur. 12. When the adhesive has been sufficiently loosened or has been cut, use the handle on the Battery Inlay Removal Fixture to open the phone.

PAGE 22

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

13. Use the Thin Plastic Spudger to break the suction on the suction cups attached to the Battery Inlay.

14. Use the Thin Plastic Spudger to break the suction on the suction cups attached to the Battery Inlay. You may need to repeat this process on some suction cups.

15. After all the suction cups have been released, carefully remove the alignment pin from the Headset Jack as shown.

16. Carefully slide the phone out of the Battery Inlay Removal Fixture.

PAGE 23

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Inlay Removal Method B 1.

Follow preheating steps described on page 18.

2.

Use a Suction Cup tool to hold the Battery Inlay firmly and create a gap between the Battery Inlay and the phone.

3.

Use the Shim to disengage the Battery Inlay from the all sides of the Rear Housing.

// CAUTION // Do not insert the shim more than 10 mm to prevent damaging internal components.

4.

Use the Shim to loosen or cut the adhesive holding the Battery Inlay. If necessary, reheat the phone as you work your way around the edges of the phone.

// CAUTION // Use care not to bend the Battery Inlay. Damage to the phone may occur.

PAGE 24

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

5.

Use the Plastic Shim to disengage the Battery Inlay in the direction shown.

6.

Carefully lift the Battery from the Rear Housing.

PAGE 25

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Inlay Removal Completion NOTE Finger Print Sensor Deco cannot be recovered and reused. 1.

Use flat end of the Black Stick to remove the Finger Print Sensor Flex from the Battery Inlay.

2.

Remove the Battery Inlay from the Rear Housing.

PAGE 26

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Screw Tampering Label Inspection NOTE If a Screw Tampering Label is damaged, the phone’s warranty no longer applies. Inspect the Screw Tampering Labels located on the top-right corner and on the bottom of the Rear Housing as shown. Verify they are correctly placed and examine them for signs of tampering.

PAGE 27

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Finger Print Sensor Flex Removal NOTE The Finger Print Sensor Flex can be recovered and reused after removal. 1.

Use the Torque Driver to loosen the screw holding the rail on the Finger Print Sensor Flex Cover.

2.

Use the Metal Tweezer to remove the Finger Print Sensor Flex Shield as shown.

3.

Use the flat end of the Black Stick to remove the Finger Print Sensor Flex.

PAGE 28

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear Housing Removal NOTE The Rear Housing can be recovered and reused after removal. 4.

Use the Torque Driver to loosen the screws holding the Rear Housing as shown.

5.

Insert the pointed end of the Black Stick in the gap on both sides of the Rear Housing.to lift up along the edges of the phone.

6.

Use your fingers to carefully lift the Rear Housing.

PAGE 29

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear-Facing Imager Deco and Imager Lens Removal NOTE The Rear-Facing Imager Deco and Imager Lens cannot be recovered and reused after removal. 1.

Set the Hot Plate to 80 °C (176 °F).

// CAUTION // Do not set the Hot Plate temperature higher than 80 °C (176 °F). Damage to the phone may occur.

NOTE Preheating with an oven is also acceptable if the oven is set to the same temperature. 2.

Place the Rear Housing on the Heating Plate as shown.

3.

Wait 5 minutes for the adhesive to warm up.

4.

Remove the phone from the Heating Plate or the oven.

// CAUTION // Wear protective gloves when handling heated components.

NOTE Perform the removal procedure before the Rear Housing starts to cool off.

PAGE 30

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

5.

Use the pointed end of the Black Stick to push the Rear-Facing Imager lens from the RearFacing Imager Deco.

6.

Use the Shim to lift the Imager Lens from the pocket on the Rear-Facing Imager Deco as shown.

PAGE 31

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Water Detection Label Inspection NOTE If the Water Detection Label (WDL) is activated, the phone’s warranty no longer applies. Inspect the WDL visible on the Rear Housing. Examine it for signs of activation.

PAGE 32

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Main PCB Removal NOTE The Main PCB can be recovered and reused after removal. 1.

Use the Shim to remove the Battery Flex BtB Connector from the pocket on the Rear Housing.

2.

Use the Tweezer to peel off the Kapton Tape from the Display Flex BtB Connector on the Main PCB.

3.

Use the Shim to disconnect the Side-Key Flex from the ZIF Connector as shown.

4.

Use the Tweezer to disconnect Side-Key Flex Connector as shown.

PAGE 33

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

5.

Use the Shim to disengage the Main PCB BtB Connector from the Main PCB.

6.

Use the Shim to disconnect the Display Flex Connector as shown.

7.

Use the Tweezer to disengage the Coax Cable Connector from the Main PCB.

8.

Use the Torque Driver with ph00 Bit to remove the Screws shown.

PAGE 34

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

9.

Use the flat end of the Black Stick to lift the Main PCB.

10. Remove the Main PCB from the Front Housing.

PAGE 35

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Earpiece Speaker Removal NOTE

517B

Remove the Earpiece Speaker only if it is defective or damaged. Once you remove it, you cannot reuse it. 1.

Use the flat end of Black Stick to pry the Earpiece Speaker from the pocket on the Front Housing.

2.

Remove the Earpiece Speaker from the Front Housing.

PAGE 36

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Factory Track ID Label Removal NOTE

517B

Remove the Factory Track ID Label only if it is defective or damaged. After you remove it, you cannot reuse it. You will need to reprint and attach a new label. Use the Metal Tweezers to remove the Factory Track ID Label from the CPU shield on the PCB.

PAGE 37

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Headset Jack Grommet Removal NOTE

517B

The Headset Jack Grommet can be recovered and reused after removal. Use the Tweezer to remove both side of the Headset Jack Grommet from the Main PCB.

PAGE 38

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear-Facing Laser Rubber Removal NOTE The Rear-Facing Laser Rubber can be recovered and reused after removal. Use the Tweezer to lift the Rear-Facing Laser Rubber from the Main PCB.

PAGE 39

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear-Facing Imager Removal NOTE The Rear-Facing Imager can be recovered and reused after removal. 1.

Use the Thin Plastic Spudger to disengage the Rear-Facing Imager BtB Connector from the Main PCB.

2.

Use your fingers to lift the Rear-Facing Imager from the opening in the Main PCB.

PAGE 40

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Front-Facing Imager Removal NOTE The Front-Facing Imager can be recovered and reused after removal. 1.

Use the Shim to disengage the Front-Facing Imager from the Main PCB as shown.

2.

Use your fingers or Tweezer to remove the Front-Facing Imager from the Main PCB.

PAGE 41

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Front-Facing Camera Rubber Removal NOTE The Front-Facing Camera Rubber can be recovered and reused after removal. Use the Tweezer to remove the Front-Facing Camera Rubber as shown.

PAGE 42

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Proximity Sensor Grommet Removal NOTE

517B

The Proximity Sensor Grommet can be recovered and reused after removal. Use the Tweezer to remove the Proximity Sensor Grommet from the Main PCB.

PAGE 43

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Shield Heat Spreading Pad Removal NOTE

517B

Remove the Shield Heat Spreading Pad only if it is defective or damaged. Once you remove it, you cannot reuse it. Use the Tweezer to peel off the Shield Heat Spreading Pad from the Main PCB as shown.

PAGE 44

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Removal /// WARNING ///

// CAUTION //

Failure to adhere to Safety Critical Note(s) may increase risk of rupture, burning, or failure to function safely when used by the customer. Refer to the Battery Safety Guidelines.

Handle the Battery Pack with care. If dropped to the floor, it may be internally damaged and must be scrapped. Ensure Battery and its insulation are not damaged (e.g. scratched, dented, punctured) prior to and throughout assembly. Prior to assembly, ensure Battery edges and surfaces are not dented or deformed, and that fixtures and parts that will contact the Battery are free of foreign material. Ensure screws and screwdrivers do not contact the Battery.

NOTE The Battery cannot be recovered and reused after removal. 1.

Set the Hot Plate to 80 °C (176 °F).

// CAUTION // Do not set the Hot Plate temperature higher than 80 °C (176 °F). Damage to the phone may occur.

NOTE Preheating with an oven is also acceptable if the oven is set to the same temperature. 2.

Place the phone in the Heating Plate, with the Display side down.

3.

Wait 10 minutes for the adhesive to warm up.

PAGE 45

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

4.

Remove the phone from the Heating Plate or the oven.

// CAUTION // Wear protective gloves when handling heated phones.

NOTE Perform the Display removal procedure before the phone starts to cool off. 5.

Use the Thin Plastic Spudger to cut the adhesives underneath the Battery from all sides.

6.

Use your fingers to carefully lift the Battery.

PAGE 46

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Side-Key Flex and Side Key Removal NOTE The Side-Key can be recovered and reused after removal. 1.

Use the Tweezer to separate the Side-Key Metal from the recess in the side of the Front Housing as shown.

2.

Use the Shim to disengage the Side-Key Flex as shown.

3.

Use the Tweezer to remove the Side-Key Flex as shown.

4.

Use the Tweezer to push out the Volume-Key frame and Power Key from the Rear Housing as shown.

PAGE 47

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Lower PCB and Cover Removal NOTE The Lower PCB can be recovered and reused after removal. 1.

Use the flat end of the Black Stick to disengage all the Main Flex BtB Connector from the Lower PCB.

2.

Use the Torque Driver to remove the 4 M1.4 screws from the Lower PCB.

// CAUTION // Use care for while handling the two screws in center. Use the Tweezer if needed.

3.

PAGE 48

Use fingers to split the Lower PCB Cover from the Front Housing.

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Main Flex Removal NOTE Remove the Main Flex only if necessary. After you remove it, you cannot reuse it. Use fingers to peel off the Main Flex from the Front Housing as shown.

PAGE 49

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Coax Cable Removal NOTE Remove the Coax Cables only if necessary. After you remove it, you cannot reuse it. 1.

Use the Torque Driver with ph00 bit to remove the screw from the Sub Board.

2.

Use your fingers to split the Lower PCB from the Cover.

3.

Use the Plastic Tweezer to remove the Coax Cable.

PAGE 50

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

USB Grommet Removal NOTE Remove the USB Grommet only if necessary. After you remove it, you cannot reuse it. Use the Tweezer to remove the USB Grommet from the Lower PCB as shown.

PAGE 51

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Vibrator Removal NOTE The Vibrator can be recovered and reused after removal. 1.

Use the flat end of the Black Stick to disengage the Vibrator from Rear Housing as shown.

2.

Use your fingers to remove the Vibrator from the Rear Housing as shown.

PAGE 52

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

PARTS REFRESH Tools Required for Parts Refresh The following tools are required for parts refresh of the Moto E Plus (5th Generation) ROW phone.

Description

Part #

Black Stick

--

Black Stick

--

--

Tweezers

--

--

ESD Mat

--

--

Wrist Strap

--

--

Isopropyl (ISP) Alcohol

--

--

Cotton Swabs

--

--

Cleaning Pads

--

--

Gloves or Finger Collets

--

--

PAGE 53

Image

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Front Housing Cleaning 3.

Use Isopropyl (ISP) Alcohol and the flat end of the Black Stick to remove any excess adhesive from where the Battery was attached to the Rear Housing.

4.

Use ISP Alcohol and the flat end of the Black Stick to remove any excess adhesive from where the Main Flex is attached to the Rear Housing.

5.

Use ISP Alcohol and the flat end of the Black Stick remove any excess adhesive from where the Display and attaches to the Rear Housing.

PAGE 54

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear Housing Cleaning Use ISP Alcohol and the flat end of the Black Stick remove any excess adhesive from where the Rear Housing and attaches to the Rear Housing.

PAGE 55

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Inlay Cleaning Use the Cotton Swabs with ISP Alcohol to remove any remaining adhesive from where the RearFacing Camera Lens attaches to the Battery Cover.

PAGE 56

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

ASSEMBLY Assembly Map *Shaded parts may be eligible for parts recovery.

PAGE 57

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

PAGE 58

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Tools Required for Assembly Description

Part #

Black Stick

--

ph00 Bit (Adjustable)

--

3 mm Allen Wrench

--

Torque Driver

--

Fixture Press

19501980

Emma Inlay Alignment and Press

3-00-T9-10000

Emma Inlay Heating Plate

3-00-U1-10000

PAGE 59

Picture / Drawing

--

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Description

Part #

Manual Roller

99901103

Battery Roller Press and Plate

MR-M5-001

Moto E5 Plus Inserts

MR-M2-001-022

Micro USB Data Cable

SKN6443A

--

Tweezers (Metal)

--

--

Tweezers (Plastic)

--

--

Gloves or Finger Collets

--

--

PAGE 60

Picture / Drawing

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Side-Key Flex and Side-Key Assembly Description

Reference #

LC+Y50409395+mkey(DPgrey) LC+Y50409406+mkey(DPgold) XT1924 VolumeKey BL&5040AA000004 CS

1

XT1924 TP+LCM ASSY_GR&5079AA000015 CS XT1924 TP+LCM ASSY_GL&5079AA000014 CS XT1924 TP+LCM ASSY_BL&5079AA000017CS

2

LC+Y50409394+pkey(DPgrey) LC+Y50409405+pkey(DPgold) XT1924 PowerKey BL&5040AA000006 CS

12

LC+Y66802486+skeyfpc(AWX)

16

XT1924 Side key metal tape&5420AA000032 CS

--

1.

Place the Side-Key Flex in the pocket as shown.

2.

Use the Tweezer to secure the Side-Key Flex into the pocket.

PAGE 61

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

3.

Use the Tweezer to place the Volume-Key Frame as shown.

4.

Use the Tweezer to insert the Power Key in place.

5.

Use the Tweezer to stick the adhesive on the Side-Key Metal as shown.

6.

Use the Tweezer to insert the Side-Key Metal into the gaps on the Volume and Power keys as shown.

PAGE 62

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

USB Grommet Assembly Description

Reference #

LC+Y506010059+USBsi(DP)

-

LC+Y53219447+bopante(SBD)

15

Use the Tweezer to place the USB Grommet on the Lower PCB.

PAGE 63

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Vibrator Assembly Description

Reference #

LC+Y26223381+motor_FPC

14

XT1924 Motor FPC tape&5420AA000030 CS

--

LC+Y53219447+bopante(SBD)

15

1.

Use fingers to place the Vibrator on the Lower PCB as shown.

2.

Press down on the Vibrator for 5 seconds to secure it firmly on the Lower PCB.

PAGE 64

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Main Flex Assembly Description

Reference #

LC+Y66802482+mainfpc(AWX)

17

XT1924 TP+LCM ASSY_GR&5079AA000015 CS XT1924 TP+LCM ASSY_GL&5079AA000014 CS XT1924 TP+LCM ASSY_BL&5079AA000017CS

2

XT1924 main FPC tape&5450AA000020 CS

--

1.

Peel the Main Flex from the carrier.

2.

Use fingers to carefully place the Main Flex onto the Front Housing, sticky side down.

3.

Be sure the printing on the Main Flex is oriented in relation to the Front Housing as shown. The word Main should be near the Main PCB.

PAGE 65

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

4.

PAGE 66

Use a fingertip to secure the Main Flex to the Front Housing.

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Lower PCB and Cover Assembly Description

Reference #

LC+Y53219447+bopante(SBD)

15

LC+Y52341631+RF(DL)

18

XT1924 TP+LCM ASSY_GR&5079AA000015 CS XT1924 TP+LCM ASSY_GL&5079AA000014 CS XT1924 TP+LCM ASSY_BL&5079AA000017CS

2

XT1924 Sub Board&6818AA000040 CS XT1924-3 IN SUB PCBA

13

LC+Y46106115+screwM1.4

--

LC+Y47201563+RFcfab(LVHUI)

--

1.

Use the Tweezer to connect the Coax Cable on Lower PCB as shown.

2.

Use fingers to attach the Lower PCB to the Lower PCB Cover as shown.

3.

Use the Torque Driver to tighten the 1 M1.4 screws (0.75+-0.05 kg/cm).

PAGE 67

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

4.

Place the Lower PCB Cover onto the pocket on the Front Housing as shown.

NOTE Press down on the Lower PCB Cover until it snaps into position.

5.

Use the Tweezer to attach the Coax Cable Adhesive to the edge of the Front Housing and remove the liner.

6.

Use fingers to place the Coax Cable on the recess as shown.

NOTE Press down on the Coax Cable with fingertip to secure it firmly in place.

7.

Use the Torque Driver to tighten the 4 M1.4 screws (0.75+-0.05 kg/cm).

NOTE Press down on the Main Flex BtB Connector to connect it to the Lower PCB.

PAGE 68

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Front-Facing Camera Rubber Assembly Description

Reference #

LC+Y506010057+FCsi_5M(DP)

8

Use the Tweezer to place the Front-Facing Camera Rubber as shown.

PAGE 69

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Shield Heat Spreading Pad Assembly Description

Reference #

XT1924 shield thm pad-4GPA&5460AA000027 CS

--

XT1924 shield thm pad-BB PMU&5460AA000028 CS

--

XT1924 shield thm pad-CPU&5460AA000029 CS

--

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

Use the Tweezer to place the Shield Heat Spreading Pad on the Main PCB as shown.

PAGE 70

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Front-Facing Imager Assembly Description

Reference #

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

LC+Y26409054+L3100_Camera_500W_F

4

1.

Use fingers to place the Front-Facing Imager on the Main PCB.

2.

Use fingers to secure the Connector on the Main PCB.

PAGE 71

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Proximity Sensor Grommet Assembly Description

Reference #

LC+Y506010056+lightsi(DP)

9

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

Use the Tweezer to place the Proximity Sensor Grommet on the Main PCB.

NOTE Press down the Proximity Sensor Grommet for 5 seconds to secure it firmly on the Main PCB.

PAGE 72

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear-Facing Imager Assembly Description

Reference #

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

MDL,CAMR,12MP,L12AA00 AF 30 COB OFILM

7

1.

Use fingers to place the Rear-Facing Imager on the Main PCB.

2.

Use fingers to secure the Rear-Facing Imager on the Main PCB as shown.

PAGE 73

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear-Facing Laser Rubber Assembly Description

Reference #

LC+Y506010077+sensi(DP)

10

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

Use the Tweezer to place the Rear-Facing Laser Rubber on the Main PCB.

PAGE 74

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Headset Jack Grommet Assembly Description

Reference #

LC+Y506010055+jacksi(DP)

6

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

Use the Tweezer to place the Headset Jack Grommet on the Main PCB as shown.

PAGE 75

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Factory Track ID Label Assembly Description

Reference #

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

Use the Tweezer to place the Factory Track ID Label on the CPU Shielding Cover on the Main PCB.

PAGE 76

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Main PCB Assembly Description

Reference #

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

LC+Y66802486+skeyfpc(AWX)

16

LC+Y52341631+RF(DL)

18

1.

Use the Tweezer to place the Coax Cable on the Main PCB.

2.

Press down the Coax Cable with fingertips to secure it firmly on the Main PCB.

3.

Use the Plastic Tweezer to place the Side Key Flex on the Main PCB as shown.

PAGE 77

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

4.

Use the Plastic Tweezer to secure the SideKey Flex into the ZIF Connector door on the Main PCB.

5.

Secure the Display Flex BtB Connector and Main PCB BtB Connector to the Main PCB.

6.

Use the Torque Driver to tighten the 2 M1.4 screws (0.75+-0.05 kg/cm).

7.

Use the Tweezer to place the Kapton Tape on the Side-Key ZIF connector on the Main PCB.

PAGE 78

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

8.

PAGE 79

Use the Tweezer to place the Kapton Tape on the Display Flex BtB Connector on the Main PCB.

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Water Detection Label Assembly Description

Reference #

LC+Y70151569+LXF_L3600_A01LDI_label

--

XT1924-3 MB 3+32G_AP_DS&6818AA000042 CS XT1924-2 MB 2+16G_EMEA_SS&6818AA000035 CS XT1924-1 MB 2+16G_EMEA_DS&6818AA000041 CS XT1924-1 MB 3+32G_EMEA_DS&6818AA000039 CS XT1924-5 MB 2+16G_LA_SS&6818AA000038 CS XT1924-4 MB 2+16G_LA_DS&6818AA000036 CS XT1924-4 BR CKD PCBA

5

MDL,FNGRPRT,Emma,BLK,SLVR,Gray,O-film

--

1.

Use the Tweezer to place Water Detection Label on the Front-Facing Flash FPC as shown.

2.

Press down the Water Detection Label for 5 seconds to secure it.

PAGE 80

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Earpiece Speaker Assembly Description

Reference #

LC+Y26209646+tfospeaker

3

XT1924 TP+LCM ASSY_GR&5079AA000015 CS XT1924 TP+LCM ASSY_GL&5079AA000014 CS XT1924 TP+LCM ASSY_BL&5079AA000017CS

2

1.

Use the Tweezer to place the Earpiece Speaker carefully on the Front Housing.

2.

Make sure the Copper Contacts on the Earpiece Speaker are oriented as shown.

3.

Press down on the Earpiece Speaker for 5 seconds to secure it to the Front Housing.

PAGE 81

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Assembly Description

Reference #

LC+Y5430SK000080+BAfoam(LVHUI)

--

XT1924 TP+LCM ASSY_GR&5079AA000015 CS XT1924 TP+LCM ASSY_GL&5079AA000014 CS XT1924 TP+LCM ASSY_BL&5079AA000017CS

2

LY,HE50,AMPEREX TYP5000MAH

19

NOTE Use the fixture to assemble the Battery.

/// WARNING /// Failure to adhere to Safety Critical Note(s) may increase risk of rupture, burning, or failure to function safely when used by the customer. Refer to the Battery Safety Guidelines. 1.

Use the Tweezer to place the Battery Foam on the bottom side of the Battery.

2.

Peel 4 Battery Adhesives from the carrier.

3.

Place the Battery Adhesives on the Front Housing as shown.

PAGE 82

// CAUTION // Handle the Battery Pack with care. If dropped to the floor, it may be internally damaged and must be scrapped. Ensure Battery and its insulation are not damaged (e.g. scratched, dented, punctured) prior to and throughout assembly. Prior to assembly, ensure Battery edges and surfaces are not dented or deformed, and that fixtures and parts that will contact the Battery are free of foreign material. Ensure screws and screwdrivers do not contact the Battery.

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

4.

Use fingers to place the Battery on the Front Housing as shown.

5.

Use fingers to secure the Battery on the Front Housing as shown.

Method A Use the Manual Roller to roll over the Battery for 10 cycles to secure the Battery on the Front Housing.

NOTE For each cycle roll the Manual Roller from top to bottom of the Battery and vice versa.

NOTE Each cycle should last for 3 seconds and the Manual Roller pressure should be around 150N.

Method B 1.

PAGE 83

Go to https://sites.google.com/a/motorola.com/motos ervice-external/lmst-features/fixture-validation

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

2.

Install and open the LMST software.

3.

Login with user credentials in LMST.

4.

Look for Fixture validation use cases and click on it.

5.

Press the Power up and Volume down keys at the same time. Use the Volume up/down keys to select “Factory Mode” to turn on the device in Factory Mode.

6.

Factory Mode appears on the screen.

7.

Plug the Micro USB Data Cable into the computer, and then into the phone.

8.

The device will display a pop-up to enable the USB debugging. If not, enable the USB debugging from the device setting.

PAGE 84

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

9.

Click on the device (right side of LMST). Select the carrier and model name if device is not recognized by LMST.

10. If the device is recognized by LMST, it will display ‘Ready’ button. Click on ‘Ready’ button.

PAGE 85

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

11. Start the test after clicking on ‘Start’ button

12. Proceed with next steps before selecting ‘OK.’

13. Slide the phone into the Insert and ensure that it aligns with the end of the Insert.

PAGE 86

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

14. Place the Press plate by using the pins as guides.

15. Screw two “Steel Socket Head Screw M4 x 0.7 mm Thread, 8 mm Long” screws into the Insert as shown (the screws function as alignment to rail.)

16. Tow-in the Insert, align the screws to the holes and secure it to the rail.

PAGE 87

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

17. Ensure the fixture is well grounded and relocate the back handle if left handed.

18. Click ‘OK’ on the LMST screen.

19. Scan or enter the fixture barcode.

PAGE 88

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

20. Click ‘Ok.’

21. Follow next steps.

22. Firmly grab both handles as shown.

/// WARNING /// Make sure that the phone is oriented straight in the fixture. For successful press the phone cannot be tilted.

PAGE 89

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

23. Roll in and out until “Rolling 1” passes on LMST screen.

24. Repeat previews steps until “Rolling 2” passes on LMST screen.

25. Once test is complete, it will display result as Pass or Fail.

26. Disconnect USB cable from the phone.

PAGE 90

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

27. Remove phone from the fixture.

28. Use fingers to connect the Battery Connector to the Main PCB.

PAGE 91

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear-Facing Imager Deco and Imager Lens Assembly Description

Reference #

LC+Y50309690+BCLE(SS_bla)

22

XT1924 Bracket_top ASSY&7601AA000030 CS

20

XT1924 Cam Deco tape&5420AA000032 CS

--

XT1924 Cam lens tape&5420AA000060 CS

--

1.

Use the Tweezer to hold the Rear-Facing Imager Deco.

2.

Use the Tweezer to place the Camera Deco Foam on the Rear-Facing Imager Deco.

3.

Use the Tweezer to place the Rear-Facing Imager Deco into the pocket on the Rear Housing as shown. Press it for 5 seconds to secure it.

PAGE 92

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Rear Housing Assembly Description

Reference #

XT1924 Bracket_top ASSY&7601AA000030 CS

20

LC+Y46106126+screw_M14_16

--

LC+Y46106085+LXF_L3510_A01_SCREW

--

XT1924 rear housing tape&5420AA000028 CS

--

1.

Use fingers to place the top part of the Rear Housing gently as shown.

2.

Use the Torque Driver to tighten the screws (0.75+-0.05 kg/cm).

3.

Press down the Rear Housing to secure it firmly.

PAGE 93

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Finger Print Sensor Flex Assembly Description

Reference #

LC+Y54509532+FPstfa(LVHUI)

--

XT1924 FPS tape&5420AA000058 CS

--

XT1924 Bracket_top ASSY&7601AA000030 CS

20

LC+Y50902039+FPpreasm(LM)

24

1.

Use fingers to secure the Finger Print Sensor Flex on the Main PCB through the gap on the Rear Housing as shown.

2.

Use the Tweezer to place the Finger Print Sensor Flex Shield as shown.

3.

Use Torque Driver to tighten the screw (0.75+0.05 kg/cm).

NOTE

517B

Use the screws as shown in the image.

PAGE 94

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Screw Tampering Label Assembly Description

Reference #

LC+Y70157057+LXF_L3500_A01_Fragile_Label

--

XT1924 Bracket_top ASSY&7601AA000030 CS

20

Place the Screw Tampering Labels on the top-right corner of the Rear Housing as shown.

PAGE 95

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Inlay Adhesive Assembly Description

Reference #

XT1924 BatteryCover BL&5011AA000025 CS

11

XT1924 Batt cover gule&5420AA000056 CS

--

1.

Use Cotton Swabs and ISP Alcohol to clean the Battery Inlay bonding ledge. The Battery Inlay bonding ledge is highlighted in the photo.

1616B

// CAUTION //

Battery Inlay bonding surface cleaning is critical to the phone’s water resistance. You must thoroughly clean the surface with ISP Alcohol and allow it to dry completely.

2.

Wait for the ISP Alcohol to dry completely.

3.

Repeat the steps for 1-2 more times.

1616B

// CAUTION //

The Battery Inlay will not adhere to the Housing if the Cotton Swabs are reused. The Cotton Swabs may be used for 2 applications of the same chemical, but then must be discarded. 4.

PAGE 96

Secure the Battery Inlay Adhesive on the Fixture (3-00-T9-10000), aligning with the two pins as shown.

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

5.

Secure the Battery Inlay on the top part of the Fixture (3-00-T9-10000) with the four clips as shown.

6.

Install the two shown parts of the Fixture (3-00T9-10000) onto the Press.

7.

Press down the Fixture handle for 5 seconds to secure the Adhesive on the Battery Inlay.

8.

Take the Battery Inlay out of the Fixture.

PAGE 97

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

9.

Use the plastic Tweezer to place the Rear Facing Camera Deco adhesive on the location shown.

10. Use the plastic Tweezer to place the Finger Print Sensor adhesive on the location shown.

PAGE 98

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Battery Inlay Assembly Description

Reference #

LC+Y501110312+basm(HCgre) LC+Y501110314+bam(HCgold) XT1924 BatteryCover BL&5011AA000025 CS

11

XT1924 Bracket_top ASSY&7601AA000030 CS

20

1.

Secure the Battery Inlay with Adhesive on the top part of the Fixture (3-00-T9-10000) with the four clips as shown.

2.

Install these shown parts of the Fixture (3-00T9-10000) onto the Press and insert the phone into the fixture.

3.

Press the Fixture Press down for 5 seconds to secure the Battery Inlay firmly on the phone.

4.

Remove the phone from the Fixture.

PAGE 99

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

IMEI Label Assembly Description

Reference #

LC+Y46369167+stray(Ogrey) LC+Y46369193+stray(Ogold) XT1924 SIM Tray BL&5017AA000010 CS LC+Y46369196+ostray(Ogrey) LC+Y46369194+ostray(Ogold)

26

LBL,IMEI,IMEI,GHOST

--

Peel the IMEI Label from the liner and secure it on the SIM Door in the location shown.

PAGE 100

Lenovo Confidential Restricted: Do not share without consent from Lenovo

Lenovo Moto E Plus (5th Generation) ROW Level 2 – Service and Repair Manual

Sim Tray Assembly Description

Reference #

LC+Y46369167+stray(Ogrey) LC+Y46369193+stray(Ogold) XT1924 SIM Tray BL&5017AA000010 CS LC+Y46369196+ostray(Ogrey) LC+Y46369194+ostray(Ogold)

26

1.

Insert the SIM Tray in the transceiver as shown.

2.

Use fingers to press the SIM Tray until it secures into the transceiver.

PAGE 101

Lenovo Confidential Restricted: Do not share without consent from Lenovo